Dimensions:	Width	Height	Depth	Weight
Display	95mm	95mm	25mm	105g
Sender Unit	64mm	96mm	30mm	114g
Sensor (Attached)	45mm	51mm	30mm	Inc above
Packed Single Unit	200mm	162mm	30mm	420g
Outer Carton 24	465mm	460mm	210mm	12.3kg

 

 

 

 

 

 

 

Accuracy	<1A	1A to 3A	3A to 71A	>71A
Current RMS	Not Specified	Better than 10%	Better than 5%	Not Specified

 

Wireless Link	433MHz Radio Frequency
Wireless Range	30m in open area [walls, partitions, metal structures and electrical appliances may effect reception range.]
Display Power Supply	3 x AA/LR6/UM-3 1.5V batteries
Sender Box Power Supply	2 x AA/LR6/UM-3 1.5V batteries
Operating Temperature	5°C ~ 45°C at 85% relative humidity
Storage Temperature	-5°C ~ 60°C at 85% relative humidity

Press the UP or DOWN to select 24hr or 12hr clock.

Press UP or DOWN to select the current HOUR – then PRESS SET

PRESS UP or DOWN to select the current MINS – then PRESS SET

PRESS UP or DOWN to select the current YEAR – then PRESS SET

PRESS UP or DOWN to select DATE FORMAT required – then PRESS SET

PRESS UP or DOWN to select current MONTH – then PRESS SET

PRESS UP or DOWN to select current DAY – then PRESS SET

PRESS MODE key to select COST MODE COST display should now be 0.

Your OWL has 2 Tariff MODES with 3 Tariff settings.

SINGLE TIMED TARIFF

If you have a single tariff for all electricity use, or a complex tariff requiring a single average cost to be entered then you require a single timed tariff.

ff setting will apply a single cost to all electricity use.

ff:

1. Press [MODE] key until COST is showing on the LCD.

flashing.

3. Press UP or DOWN keys to scroll through £, € or $.

firm currency selection.

flashing ‘ON’ or ’OFF’ will be displayed on the screen along with

‘TARIFF 1’ on the bottom left hand corner.

5. Enable TARIFF 1

5.1 Press UP or DOWN keys and scroll to ‘ON’.

firm selection.

Time will be displayed on the screen.

5.3 Press UP or DOWN keys to scroll start time Hour.

firm selection.

5.5 Press UP or DOWN keys to scroll start time Minute.

firm selection.

ff 1.

5.7 Press UP or DOWN keys to scroll currency unit / KWH. (e.g. £/KWH or pence/KWH)

firm selection.

fifffirm selection by pressing

[SET] key.

flashing ‘ON’/’OFF’ will be displayed on the screen along with ‘TARIFF 2’ on the bottom left hand corner.

6. Disable TARIFF 2

6.1 Press UP or DOWN keys and scroll to ‘OFF’.

firm selection.

flashing ‘ON’ or ’OFF’ will be displayed on the screen along with

‘TARIFF 3’ on the bottom left hand corner.

7. Disable TARIFF 3

7.1 Press UP or DOWN keys and scroll to ‘OFF’.

firm selection.

ff set up is now complete.

If your tariff varies depending on the time of day, your OWL can accommodate up to 3 settings.

Using Tariff 1 and Tariff 2 settings you can set each of these to start at a given time of the day.

You can also use Tariff 3 to set a third timed setting.

This tariff setting will set your OWL up to operate at two different rates depending on time of day.

The following steps will allow you to set up a two tiered time tariff:

1. Press [MODE] key until COST is showing on the LCD.

2. Press hold [SET] key until a currency symbol is flashing.

3. Press UP or DOWN keys to scroll through £, € or $.

4. Press [SET] key to confirm currency selection.

A flashing ON or OFF will be displayed on the screen along with TARIFF 1.

5. Enable TARIFF 1

5.1 Press UP or DOWN keys and scroll to ‘ON’.

5.2 Press [SET] key to confirm selection. Time will be displayed on the screen.

5.3 Press UP or DOWN keys to scroll start time Hour.

5.4 Press [SET] to confirm selection.

5.5 Press UP or DOWN keys to scroll start time Minute.

5.6 Press [SET] to confirm selection. Currency unit per KWH will be displayed on the screen for Tariff 1.

5.7 Press UP or DOWN keys to scroll through currency unit (e.g. ‘£’ or pence)

5.8 Press [SET] to confirm selection.

5.9 Press UP or DOWN keys to scroll each figure of the tariff cost

and confirm selection by pressing the [SET] key.

A flashing ON’ or OFF will be displayed on the screen along with TARIFF 2 on the bottom left hand corner.

6. Enable TARIFF 2

Repeat steps 5.1 through 5.9 above to enable Tariff 2.

A flashing ON or OFF will be displayed on the screen along with TARIFF 3 on the bottom left hand corner.

7. Disable TARIFF 3

7.1 Press UP or DOWN keys and scroll to OFF.

7.2 Press [SET] to confirm selection.

Your two tiered timed tariff set up is now complete.

If your tariff varies after a set amount of use, your OWL allows you to set up a BLOCK amount of usage at one rate for a 3 month period, then switch to another rate for all usage after that amount has been used.

If yu set the BLOCK tariff to a start at a particular time of the day, then this amount will be applied from that start time each day becoming a third TIMED tariff in conjunction with Tariff 1 and Tariff 2 above.

Many electricity suppliers charge a BLOCK tariff where one amount is charged for the first amount of electricity

used in the quarter, thereafter there is a lower amount charged.

Following steps will allow you to set up a block tariff:

Follow the steps on page four and disable Tariff 1 and Tariff 2.

7.1 Enable TARIFF 3

7.1 Press UP or DOWN keys and scroll to ‘ON’.

7.2 Press [SET] key to confirm selection.

Date will be displayed on the screen.

8.1 Press UP or DOWN keys and scroll for a start month.

8.2 Press [SET] key to confirm selection.

Note: This will normally be the start date of your quarterly billing period. Time will be displayed on the screen.

8.3 Press UP or DOWN keys and scroll for a start time hour.

8.4 Press [SET] key to confirm selection.

8.5 Press UP or DOWN keys and scroll for a start time minute.

8.6 Press [SET] key to confirm selection.

This mode can be used to set up a third timed tariff in conjunction with Tariffs 1 & 2; the start time applies to this.

Display will show a flashing currency unit e.g. pence and ‘TARIFF 3A’ on bottom left hand corner

8.7 Press UP or DOWN keys to scroll through currency unit

8.8 Press [SET] to confirm selection.

8.9 Press UP or DOWN keys to scroll each figure of the tariff cost

8.10 Press [SET] key to confirm selection.

8.11 Press UP or DOWN keys to scroll each figure of the tariff block amount

8.12 Press [SET] key to confirm selection.

Display will show a flashing currency unit e.g. pence and ‘TARIFF 3B’ on the bottom left hand corner

9.1 Press UP or DOWN keys to scroll currency unit.

9.2 Press [SET] to confirm selection.

9.3 Press UP or DOWN keys to scroll each figure of the tariff cost

9.4 Press [SET] key to confirm selection.

Your BLOCK tariff set up is now complete.

1.

Slide down the rear cover of the transmitter to remove.

CAREFULLY insert two AA batteries into the battery holder

DO NOT REPLACE COVER AT THIS POINT.

2.

Press the base of the rear cover of the Display and rotate out. Carefully insert two of the three AA batteries into the battery holder.

Press and hold the check Button in the battery compartment of the transmitter for 5 seconds.

flash for the next 30 seconds.

Insert the third battery into the monitor and replace the battery covers on both the monitor and transmitter.

Press UP or DOWN arrow to select 24 or 12 Hr clock and PRESS SET

PRESS UP or DOWN to select HOUR - then PRESS SET

PRESS UP or DOWN to select MINS - then PRESS SET

PRESS UP or DOWN to select YEAR - then PRESS SET

PRESS UP or DOWN to select DATE FORMAT - then PRESS SET

PRESS UP or DOWN to select MONTH - then PRESS SET

PRESS UP or DOWN to select DAY - then PRESS SET.

MODE KEY - Changes display mode:

COST-ENERGY-CO2e-TIME-DATE

Hold down for 2 seconds to change

Period modes:

TOTAL-THIS/LAST PERIODAVERAGE

THIS/LAST PERIOD

SET KEY

Hold down for 2 seconds to change to SET mode.

firms the setting into memory and moves on to the next setting.

MODE & SET Key hold both for 2 secs to clear Total accumulated.

UP and DOWN arrows

In SET Mode used to change values up and down

In This Period mode

This Day, Last Day, This Week Last Week, This Month, Last Month

In Average Period mode

Day, Week, Month

(Calculated respectively from 30 day, 60 day and 90 day histories)

FROM COST SCREEN > PRESS SET AND HOLD TO ENTER

TAR 1 SETTINGS – CURRENCY – START TIME - TARIFF

TAR 2 SETTINGS – CURRENCY – START TIME - TARIFF

TAR 3 SETTINGS – CURRENCY – START TIME - TARIFF

ENERGY DISPLAY MODE > PRESS SET AND HOLD TO ENTER

VOLTS

MAX

TARGET

CO2e DISPLAY MODE > PRESS SET AND HOLD TO ENTER

UNITS

GHG Conversion rate

TIME OR DATE DISPLAY MORE > PRESS SET AND HOLD TO ENTER

24/12 Hour clock format

TIME

Date FORMAT

DATE

The OWL Micro + transmitter and sensor are one unit and cannot be separated and therefore you cannot use a large sensor with the Micro +